What Is The Reason Why The Deep Well Pump Gets Hot During Use?

Aug 26, 2022

In the process of using Deep Well Pump, it is often found that the submersible pump has a heating problem. The submersible pump manufacturer introduced the reasons as follows: when selecting a submersible pump, it is assumed that the selected model has a high lift and the actual use lift, and there is a large gap. , it will constitute an overcurrent of the motor, and it will generate heat and burn the motor. Assuming that there are too many debris in the operating environment of the Deep Well Pump, it will cause the impeller of the Deep Well Pump to be blocked, and the impeller components will not be able to rotate, and the motor will idling and heat up to burning.

When the Deep Well Pump is operating, if there is sediment entering the bearing or the open space where the impeller is connected, the failure of the bearing to work normally will also cause the body to heat up. Assuming that the Shenyang submersible pump can work, it is usually necessary to pay attention to the maintenance of the submersible pump, and repair it in time if there is a problem, so as to ensure that the operation is not affected. In addition, it is very important to purchase a high-quality deep well pump. The service life of a high-quality submersible pump is longer, and the probability of failure is relatively low, which can reduce the cost of converting and maintaining equipment for enterprises.

The submersible pump for wells is an important equipment for lifting water from deep wells. When in use, the entire unit is submerged in water to extract groundwater to the surface. The extra power supply voltage is 380V±5%, the frequency is 50Hz±1%, and the extra voltage of the motor terminal should be within the allowable deviation range of the extra voltage; the load power of the transformer should not exceed 75% of its capacity . When the transformer is far away from the wellhead, the line voltage of the transmission line should be considered. In the process of deep water pump, it is often found that the submersible pump has a heating problem. The submersible pump manufacturer introduced the reasons as follows: when selecting a submersible pump, if the selected model has a high lift and the practical use of the lift, if there is a large gap, then If the motor overcurrent is formed, it will generate heat and burn the motor. Assuming that there are too many sundries in the working environment of Shenyang submersible pump, it will cause the impeller of the deep well pump to be blocked, and the impeller parts will not rotate, and the motor will idling and heat up to burning.

When Deep Well Pump is operating, if sediment enters the bearing or the open space where the impeller is connected, the failure of the bearing to operate normally will also cause the body to heat up. Assuming that the Shenyang submersible pump can work, it is usually necessary to pay attention to the maintenance of the submersible pump, and repair it in time if there is a problem, so as to ensure that the operation is not affected. In addition, it is very important to purchase a high-quality deep well pump. The service life of a high-quality submersible pump is longer, and the probability of failure is relatively low, which can reduce the cost of converting and maintaining equipment for enterprises.

The submersible pump for wells is an important equipment for lifting water from deep wells. When in use, the entire unit is submerged in water to extract groundwater to the surface. The extra power supply voltage is 380V±5%, the frequency is 50Hz±1%, and the extra voltage of the motor terminal should be within the allowable deviation range of the extra voltage; the load power of the transformer should not exceed 75% of its capacity . When the transformer is far away from the wellhead, the line voltage of the transmission line should be considered.

In the process of using submersible pumps and deep water pumps, it is often found that the submersible pump has a heating problem. The submersible pump manufacturers introduce the reasons as follows: when selecting a submersible pump, it is assumed that the selected model has a high lift and the actual use lift has a large gap. If it is, it will constitute an overcurrent of the motor, and it will generate heat and burn the motor. Assuming that there are too many sundries in the working environment of Shenyang submersible pump, it will cause the impeller of the deep well pump to be blocked, and the impeller parts will not rotate, and the motor will idling and heat up to burning.

The submersible pump for wells is an important equipment for lifting water from deep wells. When in use, the entire unit is submerged in water to extract groundwater to the surface. The extra power supply voltage is 380V±5%, the frequency is 50Hz±1%, and the extra voltage of the motor terminal should be within the allowable deviation range of the extra voltage; the load power of the transformer should not exceed 75% of its capacity . When the transformer is far away from the wellhead, the line voltage of the transmission line should be considered.